HALTECH Elite 2000/2500 GM GEN III LS1 & LS6 non DBW Terminated Harness
DESCRIPTION
SUITS: Factory EV1 injector connectors and common US style Delco/Bosch GM alternator connector. Pre-wired to connect directly to OEM 7 Pin Coil Harness Connector. WBC1/2 CAN O2 Wideband Controller ready (Controller and sensor(s) not included) INCLUDES: Engine harness with fuse block and firewall grommet. NOTES: Please confirm your alternator connector (See the product quick start guide) and order an alternator adaptor if required. (HT-040090 or HT-040090) Ignition coils and harnesses are NOT included, Please order 8 x HT-020102 and/or HT-045657 if required.
Harness overview
The fastest and most cost effective way to wire your race car or engine conversion! Simply connect a handful of labelled wires and this plug and Play product allows you to be up and running in just a few hours.
An efficient Haltech Plug'n'Play product that allows you to be up and running in just a few hours.
The quick start guide will walk you through installation of the Haltech Plug'n'Play harness into your vehicle.
The guide is accompanied by the full ECU manual and Software located on the CD or USB key provided with the ECU to refer to while completing your installation and configuration.
Harness features
This harness when installed in conjunction with a Haltech Elite ECU opens the door to virtually limitless performance modification and tuning of your vehicle.
Fully programmable systems allow you to extract all the performance from your engine by delivering precisely the required amount of fuel and ignition timing that your engine requires for maximum output under all operating conditions.
Warning
All GMC Racing items that involve increases in power greater than those required by the highway code of the country of the user, are intended only for competitive use. GMC Racing disclaims all liability for any use of the product contrary to national standards.
HT-141360
Here you can add custom original content(text, images, videos and more) for each product page.
HALTECH Flex Fuel Composition Sensor
DESCRIPTION
To be used with Haltech Platinum Sport, Platinum PRO, Elite 750, Elite 1500, and Elite 2500 ECUs and IO 12 Expander.
If you want to adapt to...
IO 12 Expander - 12 Channel withPlug & Pins Kit (CAN ID - Box A)
DESCRIPTION
The Haltech IO Expander 12 allows the user the ability to increase the functionality of their Haltech ECU by using...
Triple Channel OEM Igniter (DUMB)
DESCRIPTION
INCLUDES: Mounting bracket, thermal paste and matching plug and pins.
Warning
All GMC Racing items that involve increases in power greater than those...
HALTECH 12 Position Rotary Trim Module (Boost/Fuel/Ign etc)
DESCRIPTION
12 position rotary trim module - (Boost/Fuel/Ignition etc.)
Control your Elite functions in real-time from inside the...
HALTECH Elite 750 + Nissan Patrol Y60 & Y61 (TB45)Plug 'n' Play Adaptor Harness Kit
DESCRIPTION
SUITS: Plug 'n' Play replacement of the factory ECU for Nissan Patrol/Safari Y60 and Y61 with...
HALTECH Plug and Pins Only - 32 Pin Tyco
DESCRIPTION
SUITS: Sprint 500 & RE ECU Platinum Interceptor (non-waterproof version)INCLUDES: Pack of 32 Pins.
Warning
All GMC Racing items that...
HALTECH PLATINUM PRO PLUG-IN ECU SUBARU GDB WRX MY01-05
DESCRIPTION
If you are after a simple plug-and-play option and your car still has its original engine and wiring in it, a Plug-in ECU is...
HALTECH 1/4" Open Tip Thermocouple
DESCRIPTION
1/4" Thermocouple 1.64m (64.5") long - Pre-terminated with Mini K Type connector to suit TCA 2 or 4 thermocouple amplifier.
LENGTH: 1.64m...
HALTECH Elite 2000 + Nissan Patrol Y60 (TB42)Plug 'n' Play Adaptor Harness Kit
DESCRIPTION
SUITS: Plug 'n' Play replacement of the factory ECU for Nissan Patrol/Safari Y60 with automatic or manual...
HALTECH 7 Bar "TI" MAP Sensor THREAD: 1/8 NPT
DESCRIPTION
THREAD: 1/8 NPTINCLUDES: Matching plug and pins, -4 AN & 5mm hosetail adaptors.NOTES: "TI" MAP sensors must not be mounted directly to...
HALTECH Coolant Temp Sensor - Small Thread
DESCRIPTION
Haltech coolant temperature sensor (CTS) gives instant information about coolant fluid temperature to the electronic control unit (ECU)....
HALTECH Nexus R3 Tube Mount Kit - 1.625"DESCRIPTIONSUITS: NEXUS R3 VCUINCLUDES: 1 x Mounting Plate, 2 x 1.625" Tube Clamps. NOTES: Brackets are made from CNC machined 6061 Aluminum and then...
HALTECH Plug and Pins Only - AMP 26 & 34 Pin 4 Row 3 Keyway Superseal Connector Set
DESCRIPTION
Spare caps and spins. 26 and 34 Pin Amp. Plugs and Pins for different Haltech ECUs or sensors....