HALTECH Elite 2500 V8 Small/Big Block GM, Ford & Chrysler Terminated Harness INJECTOR CONNECTOR: Bosch EV1
DESCRIPTION
INJECTOR CONNECTOR: Bosch EV1 OUTPUTS: Up to 8 injector and 8 ignition. SUITS: V8 GM Small/Big Block V8 Ford Small/Big Block Chrysler HEMI INCLUDES: Engine harness with fuse block, firewall grommet and distributor/MSD ready ignition harness. NOTES: 8 individual ignition coil ready (Direct fire) when used with HT-130306, HT-130311, HT-130312 or HT-130313
Harness overview
The fastest and most cost effective way to wire your race car or engine conversion! Simply connect a handful of labelled wires and this plug and Play product allows you to be up and running in just a few hours.
An efficient Haltech Plug'n'Play product that allows you to be up and running in just a few hours.
The quick start guide will walk you through installation of the Haltech Plug'n'Play harness into your vehicle.
The guide is accompanied by the full ECU manual and Software located on the CD or USB key provided with the ECU to refer to while completing your installation and configuration.
Harness features
This harness when installed in conjunction with a Haltech Elite ECU opens the door to virtually limitless performance modification and tuning of your vehicle.
Fully programmable systems allow you to extract all the performance from your engine by delivering precisely the required amount of fuel and ignition timing that your engine requires for maximum output under all operating conditions.
Warning
All GMC Racing items that involve increases in power greater than those required by the highway code of the country of the user, are intended only for competitive use. GMC Racing disclaims all liability for any use of the product contrary to national standards.
HT-141376
Here you can add custom original content(text, images, videos and more) for each product page.
HALTECH Elite 2500 + Terminated Harness Kit For Ford Falcon BA/BF Barra 4.0L I6 - Injector Connector: Factory Bosch EV1
DESCRIPTION
SUITS: Ford Barra Engine found in BA/BF Variants Barra 182,190,...
Haltech Elite CAN CableDTM-4 to DTM-4LENGTH: 1800mm (72")
DESCRIPTION
LENGTH: 1800mm (72")
Warning
All GMC Racing items that involve increases in power greater than those required by the highway...
HALTECH Elite 2500 & 2500 T Basic Universal Wire-in Harness
DESCRIPTION
Ideal for dedicated race cars, engine swaps, and custom wiring jobs. The Universal Wire-in Harness has a set of ECU...
HALTECH Plug and Pins Only - Delphi 3 Pin Pressure Sensor Connector
DESCRIPTION
SUITS: HT-010110 - 5 Bar TI MAP Sensor HT-010138 - 5 Bar Motorsport MAP Sensor HT-010130 - 7 Bar TI MAP Sensor...
HALTECH Flex Fuel Fittings 3/8 "GM Spring Lock" -6AN Male
DESCRIPTION
SUITS: GM Flex Fuel Sensors.INCLUDES: Two fittings.
Warning
All GMC Racing items that involve increases in power greater...
HALTECH Bosch 82mm Electronic Throttle Body - Includes connector and pins
DESCRIPTION
DIAMETER: 82mm
SUITS: Nexus and Elite VCU's and ECU's that support Drive by Wire Throttle Control (DBW)....
Triple Switch Panel Only
DESCRIPTION
INCLUDES: Triple panel and yellow and red adjustment knobs.NOTES: 12 Position Rotary Trim Modules are NOT included, Please order 3 x HT-010504 if required....
HALTECH Plug and Pins Only - Matching Set of Deutsch DT-2 Connectors (DT06-2S + DT04-2P) - ( 13 Amp)
DESCRIPTION
INCLUDES: 1 x DT04-2P Connector 1 x DT06-2S Connector 2 x Wedge Locks to suit 4 x...
HALTECH 1/4" Open Tip Thermocouple
DESCRIPTION
LENGTH: 1/4 " 1.30m (51")SUITS: NA or Forced induction applications. Used with a Requires a TCA 2 or 4 thermocouple amplifier.INCLUDES: Mini K Type...